[China Glass Network] In fact, there are many places where you can see the frameless glass door. Whether it is in a hotel or a home life, the frameless glass door has a wide range of coverage. But are you clear about how to install a frameless glass door? Today Xiaobian will come to introduce you! Frameless glass door installation steps: 1. The fixed glass partition and the movable glass door fan must be unified and positioned. The positioning line of the partition and the glass door should be released according to the design drawings to determine the position of the door frame and accurately measure the ground level and the top level of the door frame. 2. Install the glass partition wall and the width of the limit groove at the top of the door should be larger than the thickness of the glass by 2 to 4 mm, and the groove depth should be between 20 and 30 mm for injection. The installation method can lead two metal decorative board edges from the center line of the bullet, and then install the limit groove at the top of the door frame according to the side line. The wooden backing plate in the notch is to adjust the groove depth. Adjust by increasing or decreasing the pad. 3. Install the wooden bottom of the metal finish. The installation method can be used to nail the square wood on the original pre-buried wood bricks, or to fix the square wood on the ground by expanding the bolts, and then sticking the metal veneer to the wooden side with the multifunctional glue. The aluminum alloy square tube can be fixed on the frame column with aluminum angle or fixed on the wooden brick buried in the ground with wood screws. 4. Install the door frame. The door frame is nailed according to the center line of the bullet, and then the plywood is used to determine the size and position of the door frame. Later, when the metal decorative surface is outsourced, the decorative face-to-head seam is placed in the middle of both sides of the mounting glass. The seam location must be accurate and vertical. 5, glass installation. Use a glass suction cup to suck the thick glass and then hold the suction cup to lift the thick glass plate through 2 to 3 people and erect it to the installation site to be in place. Placement method: Insert the upper part of the glass into the limit groove at the top of the door frame, then place the lower part of the glass on the center line on the bottom support, and install the position of the door frames on both sides so that the sides of the thick glass are just right. The metal fittings that seal the door frame face the seams, and it is required that the seam joints are not visible inside or outside. 6, the glass is fixed. Two flat square strips on the bottom and bottom of the bottom are sandwiched by thick glass, but a gap of about 4 mm is required from the thick glass, and then the multi-purpose glue is applied to the flat strip to decorate the metal. The board is stuck on the square wood and two flat wooden strips. 7, injection glass seal. Glass glue is injected into the gaps on both sides of the top root groove and on both sides of the glass tray and between the thick glass and the door frame column. The order of injection should start from the end of a certain gap to the end, and must not stop in the middle. The essentials of operation are: the force of the caulking gun should be uniform, and the speed of moving along the gap should be uniform. That is, as the glass glue is extruded, the glue injection port is moved at a constant speed to make the glass glue form a uniformity in the gap. Straight line. Afterwards, scrape off the excess glass glue with a plastic sheet and wipe the glue with a clean cloth. 8. Docking between the glass. The thick glass plate of the fixed part must be assembled by two or more pieces because the width is too large. The two pieces of the splicing must form a joint, and the joint should be kept at a distance of 2 to 3 mm. After the glass is fixed, it should be glued into the gap with glass. After filling, the plastic sheet should also be used to flatten the glue to make the gap form a clean and uniform straight line. The glass surface should be cleaned with a clean cloth. Thick Satin Fabric,High Quality Satin Fabric,Polyester Thick Satin Fabric,Recycled Polyester Satin Thick Fabric Shaoxing Linkloom Import and Export Co.,ltd. , https://www.linkloomtextile.com